The cones, set screws and center bracket still hold twist even after one coil breaks, and a slipped tool there can break bones. Leave all of it alone, keep children and pets away from the header, and keep your car out of the doorway.
Service · Garland, TX
Broken Torsion Spring in Garland, TX
A sharp bang came from the header over your garage door, and the coil on the steel shaft now shows a clean gap. A broken torsion spring leaves the shaft, the drums and the cables with no twist to turn them, so your door can't climb. Stand clear of the shaft, keep the door shut, and call about the torsion spring at your Garland garage.
What you are seeing
How a torsion break shows up
Torsion springs sit on a steel bar across the header, wound tight so they turn a drum at each end. A break leaves marks you can spot from the floor without touching anything.
- One sharp report
The coil split under tension, usually with the door down.
- Clean gap in the coil
Two lengths of spring sit a few inches apart on the bar.
- Door climbs an inch or two
It lifts slightly and halts, or does not move.
- Cables off the drums
The lift cables sag or have jumped their grooves.
- Shaft shifted
The bar sits off center, or a drum has slid along it.
Safety protocol
Hands off the winding hardware
Loss risk
What a split coil does to the shaft
A torsion spring stores the twist that offsets your door's weight. Once the coil splits, the bar stops helping, and the drums, cables and center bracket take strain they were never built for.
- Tiring twin
On a two-spring bar, the surviving coil does the work of both and gives out early.
- Scored drums
Cables that jump their grooves gouge the drum and kink their strands.
- Flexed bar
Lifting a door off balance bends the shaft and wears its end bearings.
- Dished top panel
Dragging a dead door bows the highest panel inward.
Keep your hands off the shaft, the cones and the drums, then call about the torsion spring.
(817) 330-7674Local detail
A torsion break in a Garland garage
A coil that splits overnight can leave the door down with the car inside. Leave your Garland door shut, stay off the bar, and call about the torsion spring.
Property type
One coil on the bar or two
Lighter doors hang on a single coil, and heavier or wider doors use a pair side by side.
When one of a pair breaks, the other has run the same cycles and sits close to its end. If your bar carries two coils, plan on both changing together.
Repair scope
What torsion spring service involves
Torsion work brings the stored twist under control before any part moves, with winding bars and the training to use them.
- Shaft hardware assessed
The bar, end bearings, center bracket and drums get checked for wear and bending.
- Coils specified
New springs fit your door by wire gauge, length, inside diameter and left- or right-hand wind.
- Turns counted
Each coil takes the number of turns your door's weight and height call for.
- Cable ends seated
Each cable sits in its drum groove at matching tension, so both sides rise together.
Service sequence
From the split coil to a level door
Door kept shut
You leave it closed and keep people and pets away from the shaft.
Shaft assessed
The bar, bearings and drums are checked for what the break damaged.
Coils fitted
New coils go on the bar, sized to the door and wound under control.
Lift trued
The door holds at any height and rises level on both cables.
Triage order
Why a split coil needs a call before the next press
A door left on a broken torsion spring puts its load on the cables, the drums and the opener, and each press wears them. Call from Garland or anywhere in Dallas County while the damage still sits in the coil.
Service area
Garland ZIP codes
- 75040
- 75041
- 75042
- 75043
- 75044
- 75045
- 75046
- 75047
- 75049
Every responding technician is independent. Before work begins, confirm the technician's license, insurance and pricing with them directly.
Common questions
Broken torsion spring questions in Garland
Why does the door stay down after the bang?
The coil that carried the door's weight has split, so nothing lifts it. The opener cannot make up that weight, and running it only wears the drive.
Can you wind a new torsion spring yourself?
No. A wound torsion spring holds enough twist to snap a tool loose with force, and the winding takes bars and training. Leave it to the trade.
Does one broken coil mean the other needs changing?
On a two-coil bar, usually yes. Both have run the same cycles, so the second is close behind.
A door held by a broken spring is a door waiting to drop.
Call from Garland before a broken spring or cable strips the opener or bends the sections.