A broken side spring leaves metal under load along both edges of the opening. Stay in the middle of the bay, away from the tracks, and keep children and animals out of the garage altogether.
Service · Garland, TX
Garage Door Spring Conversion in Garland, TX
Your garage door still hangs on extension springs beside the tracks, and one has stretched, rusted or snapped. A garage door spring conversion moves the lift to a torsion bar above the opening, with springs wound on a shaft and cables running to drums. Keep clear of the springs, and call about a spring conversion for your Garland garage door.
What you are seeing
Why failing side springs point to a conversion
Extension springs wear out in ways a torsion bar does not, and a few patterns say your door is ready for a different lift.
- Repeat breaks
A side pair that has already needed replacing once.
- Crooked rise
One edge of the door trails the other on the way up.
- Extra load
Added glass or insulation outgrows what side springs can carry.
- Exposed hardware
Springs and cables run along the track where a car, a bike or a hand can snag them.
Safety protocol
Keep clear of both sides of the door
If anyone is hurt, call 911 first.
Loss risk
Why side springs keep coming back
A door lifted at its edges takes pulls that never quite match, and each failure sends damage into the hardware around it.
- Repeat calls
Each failed pair brings the same fault back within a few seasons.
- Rail scuffing
Rollers on the short-changed side scrape the rail.
- Ragged rise
The door jolts or climbs crooked once the springs stop matching.
- Fewer moving parts
A bar turns in place, while side springs travel along the track with every pass.
A door that keeps breaking side springs is a candidate: call about moving the lift to a torsion bar.
(817) 330-7674Local detail
A door on side springs in a Garland garage
Doors still on side springs predate most bar systems, and their springs age out first. If that is your Garland garage, call before the pair fails again.
Property type
Does the opening suit a bar
A torsion bar mounts to the framing above the opening, so the header needs enough sound wood or metal to hold the bar's brackets.
Headroom matters too, because the bar and its drums need clear space above the door. If your header looks soft or the ceiling sits close above the door, a conversion may need added framing first.
Repair scope
What a conversion swaps in
Conversion changes the lift system and leaves the door panels, tracks and opener as they are.
- Shaft and bearings
A steel shaft and end plates carry the new springs across the header.
- Drums and cables
A matched drum and cable set takes over from the old pulleys.
- Torsion springs
Coils sized to the door's weight and height turn the shaft.
- Track hardware
The old stretch springs and their mounts leave the tracks.
Service sequence
From side springs to a bar above the door
Old lift surveyed
The side springs and their cables show how far the lift has aged.
Framing proven
The wood or metal above the opening shows it can hold the new bar.
New system built
Shaft, drums, cables and torsion springs go on, each set under control.
Door returned
It rises plumb and holds at any height.
Triage order
Why converting beats swapping the same springs again
A failed side pair that you simply replace brings the same failure back with the same risk to the bay.
Call from Garland or anywhere in Dallas County and ask whether your door suits a torsion bar. A bar turns in one place, so the door rises with less shake and less noise from the tracks.
Service area
Garland ZIP codes
- 75040
- 75041
- 75042
- 75043
- 75044
- 75045
- 75046
- 75047
- 75049
Every responding technician is independent. Before work begins, confirm the technician's license, insurance and pricing with them directly.
Common questions
Garage door spring conversion questions in Garland
Does a conversion replace the whole door?
No. It changes the springs, the shaft and the cables. The door panels and the opener stay as they are.
Is a torsion bar safer than side springs?
A torsion spring sits on a bar and cannot swing loose along the track, which removes the swing-loose risk of a side spring.
Can every door take a conversion?
Most can, if the framing above the opening is sound and there is room for the bar. The header decides it.
Does one coil or two serve the new bar?
A small, light door runs on a single coil, and a heavy or broad door takes a pair. Your door's weight sets the count.
A door held by a broken spring is a door waiting to drop.
Call from Garland before a broken spring or cable strips the opener or bends the sections.